Takeuchi TW80 Series 2 Wheel Loader

The TW80 SERIES 2 Wheel Loader provide many features that operators demand in today’s compact wheel loaders. These loaders now feature a spacious operator’s cabin with factory installed air conditioner and heat for improved operator comfort in all weather conditions. The new water cooled Deutz engine is Final Tier 4 compliant using a maintenance free diesel oxidation catalyst (DOC) to reduce emissions and minimize downtime. Additionally, both models are now available with road gear allowing them to achieve travel speeds up to 25 mph, high flow auxiliary hydraulics providing greater attachment versatility, and ride control improving load retention and ride characteristics. Couple these new features with the loaders already impressive working range and operating capacity and you have a loader that is ideal for a wide variety of applications.

Performance. Durability. Operator Comfort. Serviceability.

Click the tabs below to view the Takeuchi TW80 Series 2 Wheel Loader product specifications.

7 ft 2.6 in (2,200 mm)
Outside Turning Radius
13 ft 3 in (4,046 mm)
Max Lift Height to Bucket Pin
11 ft 1 in (3,380 mm)
Bucket Clearance Height
9 ft 11 in (3,025 mm)
Dump Height Fully Raised
8 ft 6 in (2,605 mm)
Max Dump Angle Fully Raised
45 Degrees
Max Bucket Rollback at Ground Level       
48 Degrees
Reach Fully Raised
2 ft 5 in (740 mm)
Overall Width Without Bucket
6 ft 9 in (2,050 mm)
Overall Height
8 ft 11.5 in (2,730 mm)
Overall Length With Bucket
18 ft 3 in (5,580 mm)
Minimum Ground Clearance
18.5 in (470 mm)
Loader operating information and dimensions are based on the standard machine
configuration 1.3 cu. yd. bucket, 400 170 R20 tires, 165 lb (75 kg) operator.  
information is affected by different configurations and attachments

Hydraulic Reservoir Capacity      
14.0 gal (53.0 L)
Auxiliary Hydraulic Flow
Hydraulic Auxiliary Hydraulic Flow
16.4 gal/min (62.0 L/min)
26.0 gal/min (98.0 L/min)
Auxiliary Hydraulic Pressure
3,335 psi (23.0 MPa)

Loader Boom Linkage Type
Z-bar pattern
Standard Weight (w 165 lb operator)      
Standard machine with bucket
12,700 lb (5,760 kg)
Tipping Load, Straight
10,065 lb (4,565 kg)
Tipping Load, Full Turn
8,890 lb (4,033 kg)
ROC with bucket * (SAE J818)
4,445 lb (2,016 kg)
Bucket Breakout Force
13,960 lb (6,333 kg)
Lift Arm Breakout Force
12,387 lb (5,618 kg)
Traction Force
11,802 lb (5,354 kg)
Cycle Time
Raise – Full Load
6.0 (Seconds)
Lower – No Load
3.8 (Seconds)
Dump – Full Load
1.2 (Seconds)

* Operating Capacity is 50% of full turn tipping load
with bucket according to SAE J818 

Deutz TD2.9L Turbo
Tier Rating
EPA Final Tier 4
4/176 cu in (2.9 L)
Horsepower Gross (SAE J1995)
73 hp (54 kW)
Horsepower Net (SAE 1349)
67 hp (50.0 kW)
Rated Engine Speed
2,200 rpm
Maximum Torque
192 ft-lb @ 1,800 rpm (260 Nm)
Engine Lubrication
11.6 qt (11.0 L)
Fuel Tank Capacity
26.4 gal (100 L)
Fuel Consumption (65% of full load)       
2.6 gal/hr (10.0 L/hr)
Electrical System
12 volts / 95 amps

Transmission Type
Hydrostatic Drive with 100% Hydraulic Inching Pedal
Axle Type
Rigid Axles With Outboard Planetary Reduction
Differential Lock
100% Differential Lock in Front and Rear Axles
Parking Brake
Spring Applied, Hydraulically Released, Multiple Wet Friction Disk
Service Brakes
Hydrostatic and Multi Wet Friction Disk
Tire Gauge
Steering Articulation
40 Degrees Left / 40 Degrees Right
Frame Oscillation
12 Degrees Left / 12 Degrees Right
Maximum Travel Speed      
 Road Gear 24.8 mph (40 km/hr)
Low Range
4.0 mph (6.5 km/hr)
High Range
12.4 mph (20 km/hr)


  • EPA Final Tier 4 compliant, turbocharged, water cooled
  • Dual element air cleaners with restriction indicator
  • High capacity radiator


  • Electronic engine monitoring system with fuel gauge, high beam indicator, turn signal indicators, high speed indicator
  • 12 Volt system with 95 amp alternator
  • Work lights, front and rear
  • Driving lights and turn signals
  • Directional lights, Fwd / Rev
  • Engine preheat
  • Back-up alarm
  • Horn


  • Hydrostatic drive with 100% inching pedal
  • 100% Locking differentials, front and rear
  • Outboard planetary drives
  • 2-Speed travel
  • Spring applied parking brake
  • Multi wet disc brake
  • Available Heavy duty construction tire assembly
  • Available Flotation tire assembly
  • Available high speed road gear with ride control (24.8 mph)


  • Pilot controls
  • Proportional thumb wheel control for auxiliary hydraulics
  • Auxiliary lines plumbed to the end of the loader arms
  • Auxiliary hydraulic detent
  • Hydraulic system test ports
  • Hydraulic oil level sight gauge
  • High capacity hydraulic oil cooler


  • Z-bar loader linkage
  • Bucket float function
  • Mechanical bucket positioning
  • Hydraulic bucket quick coupler
  • Self aligning loader bushings with oversized pins
  • Available 77″ Construction combo bucket (1.05 cu yd)
  • Available 81.5″ GP combo bucket (1.05 cu yd)
  • Available 82″ bolt-on-blade
  • Available Combo hitch to universal SSL adaptor
  • Available HD 48″ Pallet forks and frame
  • Available Flat face hydraulic coupler kit


  • ROPS / FOPS Level 2 Cab with front and rear wipers, rear window defrost, and heater
  • 2″ Retractable seat belt
  • Adjustable suspension seat with arm rest
  • Large steps and grab handles
  • Elevated operator’s station
  • Multi-function joystick for machine direction (Fwd / Rev), and loader controls (Raise, Lower, Curl, Dump)
  • Air conditioner
  • Available 3″ retractable seat belt

Click on the images below to enlarge.

Call Us Today at 1-800-DURANTE for a Free Quote or to Schedule a Demo.